Roman column as a decoration, usually white, long time of the outside air, contact surface is easily covered with dust, pollution into the grey and black. Aesthetic impact. For the surface dust, must promptly clean up. The Roman column is the raw material of gypsum, can not use water to clean the wash would be more dirty, gypsum contact with water will absorb, resulting in cylinder bubbling, serious will be broken, weathering, shedding, spit yellow, water spots and so on. To clean up the Rome column with a soft cloth gently wipe the column, can also use the feather duster often swept surface.

　　If the surface contamination on the ink or not wipe off stains, need to use a knife to gently scrape the surface stains, then to repair. After the repair, and then fine sandpaper repair uneven places, until smooth and polished to.

　　In addition, the Rome column can be said to be a kind of breathing material, in order to keep the Roman column smooth breathing, should avoid covering the sundries in the Rome post, otherwise Rome column under moisture can not through the surface of the pores play, a serious cause of Rome column deformation.

　　To make a long story short, in a word in daily life, should be timely maintenance of Roman column. Only the good maintenance, can better show the Roman column.

　　When the Roman column in the choice of what to note there is? Xiaobian for you a summary.

　　Roman column although good decorative function, but in the use of the process must consider the coordination with the surrounding environment, especially a variety of color combinations. In general, the living room, large areas of ” public space ” the ground is best to use white, beige, light color, because of light and diversiform, the furniture can achieve perfect combination, give you more mercurial personality stage.

　　1, whether to a small staircase noise: stairs must not only strong, safe, beautiful, it also should not make too much noise. On the stairs out ” thump, thump ” sound is often very terrible, especially when in the dead of night. The noise and the staircase of the material and overall design of a relationship, but also connected with each part of a relationship.

　　2, the stairs are use environmental protection material: as the furniture is made of materials composed of the same, railing support this “furniture ” is from the ” material” of composition, such as solid step through the painting process. It is easy to be ignored. Remind everybody in the choice of stair style, also to care about whether it is composed of the environmental protection material, its production process is environmental protection. Don’t let the stairs emit harmful chemicals.

　　3, whether to eliminate acute railings: stairs of all parts should be smooth, fruity, sharp parts did not highlight, so as to avoid unintentional damages to users. Just imagine, when the ladies wearing skirts, flying like gone with the wind to go upstairs, go ahead, behind to hang up, will produce what kind of visual effect. At the same time the stairs pedal, should pay attention to deal with rounded corners, to avoid damage to the feet.

　　4, stair baluster handrail and: if the metal as the stairs and railings, so the best manufacturers in the metal surface to do some processing, especially in the north, the metal in winter when cold feeling, can let a person particularly uncomfortable, it is especially important for the elderly. The handrail is a special material on the market at present, both metallic cool, but not cold. At the same time the staircase handrail diameter of 5.5 cm is appropriate, because the skin is generally 5.5 cm, up will be very comfortable.

　　The railing, staircase width 5: should consider the possibility of child collet, or is the head of the child not to go, either a free pass. Railings spaced with 8 centimeters advisable, because 8 cm intervals can prevent child playfully put your head in.

　　6, construction is quick, convenient stairs: choose the stairs also select installation way of the stairs. Fast, convenient installation for you and your neighbor will have significance. Convenient installation in the installation process will reduce the noise and dust to a minimum. But need to weld the stairs there are hidden dangers in the installation process, the smell and dust is the home furnishing environmental pollution.

　　7, stairs lighting is exquisite: from the staircase position, give people the feeling is mostly dark, so the light source design becomes particularly important. The main light source, a light source, lighting and other aspects according to practical situation, too dark lighting is not conducive to the safety of walking, too bright and prone to glare, so the light will have reached a certain degree in the soft and clear.

　　1, the line on the surface layer has been completed and mark each railing post position

　　2, the hammer drill to bore a hole in the post office, depth is 50mm, wherein the first step and the second step bottom depth is 100mm, diameter of drill with the column diameter.

　　3, with a hammer column reinforced in borehole. Column reinforced length of column height and 50 ( 100 ) mm.

　　4, the floral parts into the column reinforced.

　　5, in section 40mm * 80mm and 40mm * 100mm square blocks ( 1 40mm ×100mm square by the spacing and number of lofting column reinforced saw hewn gap ), timber length with handrails, the column reinforced with square notch, and 12 wire two pieces of timber temporary tie clip from the top of the columns about 50mm, then the whole correction column and brace.

　　6, on the top of the columns bomb inclined line, then the graphite pen line, and then use the oxygen will column reinforced top blowing cut into inclined surface.

　　7, welding arm flat iron, then in the flat iron bending, warping, using acetylene heated red lining, water cooling, and immediately correct the flat iron. And then welded corner flat iron, be armrest at both ends of the connection corner flat iron welding, tie clip removal in column reinforced at the top of the square.

　　8, a weld trim.

　　9, installation of wooden or plastic armrest.

　　In order to produce the method of faux marble pillar effect is most effective, careful selection of paint and colored glaze, and then alternate between the two on the substrate white or light-colored, so you can create textures and grain imitation of natural marble. This process is called ” marble “, can be used for walls and furniture. Although it is time consuming, but the effect is quite amazing, very worth spending the time and energy to try.

　　In order to achieve satisfactory results, must choose close to natural marble color to. The most effective combination is grey / white and dark grey / black stripe, pink and peach stripe and white shell or a combination of white and yellow / grey and green stripes, these are the usual natural marble color combinations.

　　Different levels of paint at regular intervals to be coated glazing until the desired effect. Of course, there are a lot of change process. In order to achieve the effect of natural nudity, some people use a feather, some people use a candle wax. This is a creative process — very interesting. You can buy Artificial marble columns, or you can make your own, either way, it will add color to your home furnishing.

　　1: Order the MaterialStep 2: Cover the BaseStep 3: Attach the Metal LatheStep 4: Apply the MortarStep 5: Apply the Stones at the BottomStep 6: Place the Corner StonesStep 7: Fit the Center StonesStep 8: Grout the SeamsStep 9: Chip the Stones if NecessaryStep 10: Trim the Corner PiecesStep 11: Scrape Down the Excess MortarStep 12: Measure and Cut the StonesStep 13: Apply a Large Amount of MortarStep 14: Create a Slight CantStep 15: Fill the Capstone Joints With GroutStep 16: Fill the VoidsStep 17: Create a Rough Edge.

　　The above 17 steps level, perfect the detailed process to be a stone pillar, our factory strictly according to this production process for the customer service be strict in one’s demands.

　　Nursing care of marble railings, handrails are more expensive, therefore need careful nursing. If improper care will cause it to be dyeing. Adhere to the daily cleaning, in order to keep the good condition for monthly require special cleaning fluid to clean the marble design. You can also consider the use of special polishing tool polishing marble railings, these tools can be from many places on loan to, or you can ask professional personage to.

　　To sum up in the installation must be careful not to damage, with great care to do good, the family installed marble baluster are some details we face in life, whether you in or not as you can learn.

　　Nursing daily marble steps:

　　Step one: every week for surface cleaning : use wet cloth to scrub with a soft, dry.

　　Step two: use neutral, non-abrasive stone renovation ( such as acetone, ammonia cleaning agent ) to deal with stubborn stains can be, apply cleanser, with a soft dry.

　　Step three: surface clean, marble polishing agent containing tin oxide surface polishing of marble.

　　Step five: Stone sealant to protect the marble floors, cleaning floor cleaner non-abrasive standard.

　　Step six: mat in the glass pad below, in the marble surface cosmetics to pad plastic pad.

　　Step seven: no matter how to repair the scratch depth, to explain to the professionals.

　　Daily marble nursing notes:

　　1, powdered detergent will scratch or damage to marble, this kind of detergent is best not to use.

　　2, even if it is weak acidic substances such as vinegar, wine, juice, cola and will damage the marble. If the liquid is spilled marble surface to promptly clean up the spill, and rinse with water.

　　3, cleaning the marble floor with warm water, because the water evaporation fast.

　　4 stone pillars, care to avoid the use of acidic cleaning agent. They will be corrosion, weak alkaline stone such as marble polishing surface.

　　A, essential difference

　　1, the marble grinding block polishing is a prelude or stone processing stone crystal surface treatment is necessary in a process. Its main principle is composed of inorganic acid, such as metal oxide material to synthesize the pressing grinding block combined with mechanical grinding pressure, high speed grinding force, friction heat utilization, the role of water in physical, chemical combination on the marble surface is smooth, thereby forming a bright crystal layer of new. The crystal layer has a bright, clear light, light up to 90-100. The crystal layer is the stone surface layer ( 1-2mm thick) of the modified compound crystal layer.

　　2, marble pillar cleaning is a prelude to waxing polishing marble, marble cleaning waxing polishing is belong to the early 80–90 popular marble cleaning and maintenance of protective measures, has now lost the market and the meaning of existence. It is the nature of the new paving stone ( polished ) a thin coating of acrylic resin and emulsion surface coverage of polymer, is what we often say that the wax or wax. After polishing machine of high speed, low pressure with fiber mat on the friction surface of the stone, the resin coating a process more bright. Because the product updates, and later special light wax, polishing wax, free, the coating is similar to wood floors oil varnish.

　　3, the marble nursing crystal surface treatment before the grinding block polishing process is a stone surface layer and the chemical physical and chemical process. The surface layer and the bottom layer of stone completely combined into a whole, does not exist out of layer.

　　A layer of wax, waxing and polishing the marble of 4 above is attached on the stone surface, a layer of resin film, there is no chemical reaction with the stone itself. The wax layer can be a shovel blade, can be cut from the film on the stone surface.

　　Two, image difference

　　1, grinding polishing marble block is the prelude of the stone care crystal surface treatment, stone care after polishing brightness high, high definition, wear resistance, step, not easy to scratch, is a stone function reflected and spread value.

　　By 2, stone polishing wax in the low post, luminosity is not clear, and very fuzzy, abrasion resistance, water resistance, easy to scratch, oxidation of yellow stone image to reduce the essence.

　　Three, extension and operation difference

　　1, stone grinding block after polishing crystal layer and crystal layer of the continuity of care ( commonly known as crystal face care ), the pores has not completely closed, stone can still inside and outside air, stone is not easy to disease. At the same time with waterproof, anti-fouling effect of certain.

　　2, the marble waxing polishing, stone pores are completely closed, stone can not be inside and outside air, so the stone prone to disease.

　　3, stone grinding block after polishing crystal layer and the crystal layer of continuity of care and operation is easy, do not need cleaning agent cleaning the ground, can be directly grinding block with water and dry grinding polishing agent. Can always polishing and nursing, local operation. Color stone surface without new contrast.

　　4, the marble waxing polishing, after a period of time, need to remove residual wax layer has been old, require the use of wax from the water. At the same time a large area of operation and construction, not local construction, local construction after the surface color appearance.

　　Four, practical significance

　　1, stone columns after polishing grinding block after polishing, luminosity is 90-100 degrees, reducing the photometric stone factory, the stone value of reproduction. Crystal surface treatment and nursing, can be more time-saving, labor-saving, cost savings, more wear-resisting performance. Waxing polishing marble, a decline in its surface photometry, fuzzy not clear, reduced stone function value, not entertaining.

　　2, the essence and appearance difference can be found: waxing polishing marble must be eliminated, fade out of the market. Because of the technological principle and method of marble polishing crystal face care is more advanced, can make the marble and more ornamental and prolong its service life.

　　One is the process of stone forming, itself has some crystalline salt component in the stone composition, two is because the acid stone and in the air, the reaction of the salt. Failure phenomenon, salt stone as follows: weathering, expansion pressure, the failure stress. Below we analyze, process marble and other stone broken how it happened:

　　As we all know, in the production, forming, handling, processing, construction process, the stone will come into contact with water in soil, cement, lime and other substances, and these substances, there will be some more or less salt, such as cleaning agent for renovation of the same, in the contact process, crack through tiny holes, stone slightly into the stone structure. When the salt in the stone structure, after the formation of a crystalline body, will bring pressure to the stone, such as the expansion pressure, the larger crystals expansion, the pressure is greater, then, structure of stone damage will be more and more. And even make stone structure became loose, easily broken or crisp.

　　Due to all kinds of pressure, in the stone structure, continue to produce stress relative, this will make the stone produced quite adverse reactions occur, powder, not smooth, massive, add water, combined with the salt damage wind, the stone surface soft, to be dissolved, then for a long time, the final failure, causing stone crack, break to pieces, not hard.